Workwear is clothing worn for work, especially work that involves manuallabour.
Often those employed within trade industries elect to be outfitted in
workwear because it is built to provide durability and safety. Work Wear,Men Work Wear,Women Work Wear,Breathable Work Clothes Greateagle Safety Products Co., Ltd. , https://www.greateaglesafety.com
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131"; Home>Bearing knowledge>Professional skills of the sliding bearing of the machine (4) Analysis of the Skills of Initiating Sliding Bearings (4)
The reason for the occurrence: the cylinder seal is poorly sealed; the coolant enters the crankcase, and the engine oil radiator is damaged; the oil and water mix, when the smooth oil is added, the water enters or the fuel filler port and the oil dip seal are bad; the washing machine and the water when it rains Entering the crankcase, there is water in the fuel entering the crankcase. So before each launch of the launching machine; be sure to check the oil level and oil quality of the smooth oil; this is necessary. /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
3. Damage to the shaft and bearing bush caused by fuel in smooth oil:
After the fuel enters the crankcase, it will make the smooth oil change. æ¹ã‘浔〗 The legs are å€ å€ å€ å²· å²· å²· 嵬咴 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . By-products that occur after fuel incineration; after being brought into the poorly ventilated crankcase by the fuel; the sulfuric acid produced will form severe cavitation on the outer surface of the shaft.
The reason for the occurrence: the fuel supply of the fuel system is too large; the fuel injected into the incineration chamber cannot be completely incinerated, the intake air is blocked by the intake air; the fuel cannot be incinerated, the nozzle seal fails, the fuel enters the crankcase, and the fuel passage in the cylinder head There are blowholes or cracks in the pores, and the idling speed is too long; the temperature of the initiator is low and the fuel cannot be completely burned.
It is necessary to prevent shaft and bearing bush damage and damage caused by smooth systems:
A. In the absence of manual smoothing equipment; when the device is started, the outer surface of each shaft and bearing bush should be coated with the same sanitary smoothing oil as the operating label; after the device is started; the fuel switch is closed before the initial launch; The starter of the movement starts to idle several times; when the engine oil pressure gauge is activated; the fuel switch is turned on again; the throttle is set at medium and low speed; the initiator is initiated to conduct the operation investigation.
B. After the start of the captain's temporary deposit; the initial launch will also be initiated after the launch of the machine shares;
C. It is necessary to protect, view, and replace the smoothing oil and filter element at the time of the rule.
D. The smooth oily surface of the initiator; it is necessary to be within the scope of the specification; it is necessary to sanitize the smooth oil and refueling; prevent the entry of any dirt and water; together to ensure the sealing effect of the various parts of the engine.
E. Prevent the start of the idling operation from being too long; the idle work cannot exceed 5 minutes.
F. It is necessary to pass the medium-speed heating operation after the initiation of the machine; when the water temperature rises above 70 °C, it is put into operation.
G. After the start of the full-load operation, the initiator can't stop immediately; it is necessary to let the initiator idle for 15 minutes after the idle speed is turned on; otherwise the internal heat will not be released.
Recommend to friends comments close window Bearing related knowledge Rolling mill bearing application bearing classification details (1)
Bearings use "four attentions" and bearing cooperation
Skf bearing angular touch ball bearing bearing depicting several difficult questions to consider
This article links to http://
Please indicate the bearing network http://
Previous: PVD skills in the bearing occupation of the next edition: the smoothness of the main bearing of cement mill and its handling
The
workwear clothing industry is growing and consumers have numerous
retailers to choose from. Chains that have made a commitment to the $1
billion and rising workwear business report steady 6 percent to 8
percent annual gains in men's workwear.
In
the UK, if workwear is provided to an employee without a logo, it may
be subject to income tax being levied on the employee for a "payment in
kind." However, if company clothing is provided with logos on then the
employee may be entitled to a tax rebate to help pay for the upkeep.
Analysis of the Skills of Initiating Sliding Bearings (4)
Source: China Bearing Network Time: 2018-06-08